[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

19.9 Comparison Operations

Comparison operators test a relation on two operands and are considered to represent a machine-dependent nonzero value described by, but not necessarily equal to, STORE_FLAG_VALUE (see section 21.21 Miscellaneous Parameters) if the relation holds, or zero if it does not. The mode of the comparison operation is independent of the mode of the data being compared. If the comparison operation is being tested (e.g., the first operand of an if_then_else), the mode must be VOIDmode. If the comparison operation is producing data to be stored in some variable, the mode must be in class MODE_INT. All comparison operations producing data must use the same mode, which is machine-specific.

There are two ways that comparison operations may be used. The comparison operators may be used to compare the condition codes (cc0) against zero, as in (eq (cc0) (const_int 0)). Such a construct actually refers to the result of the preceding instruction in which the condition codes were set. The instruction setting the condition code must be adjacent to the instruction using the condition code; only note insns may separate them.

Alternatively, a comparison operation may directly compare two data objects. The mode of the comparison is determined by the operands; they must both be valid for a common machine mode. A comparison with both operands constant would be invalid as the machine mode could not be deduced from it, but such a comparison should never exist in RTL due to constant folding.

In the example above, if (cc0) were last set to (compare x y), the comparison operation is identical to (eq x y). Usually only one style of comparisons is supported on a particular machine, but the combine pass will try to merge the operations to produce the eq shown in case it exists in the context of the particular insn involved.

Inequality comparisons come in two flavors, signed and unsigned. Thus, there are distinct expression codes gt and gtu for signed and unsigned greater-than. These can produce different results for the same pair of integer values: for example, 1 is signed greater-than -1 but not unsigned greater-than, because -1 when regarded as unsigned is actually 0xffffffff which is greater than 1.

The signed comparisons are also used for floating point values. Floating point comparisons are distinguished by the machine modes of the operands.

(eq:m x y)
STORE_FLAG_VALUE if the values represented by x and y are equal, otherwise 0.

(ne:m x y)
STORE_FLAG_VALUE if the values represented by x and y are not equal, otherwise 0.

(gt:m x y)
STORE_FLAG_VALUE if the x is greater than y. If they are fixed-point, the comparison is done in a signed sense.

(gtu:m x y)
Like gt but does unsigned comparison, on fixed-point numbers only.

(lt:m x y)
(ltu:m x y)
Like gt and gtu but test for "less than".

(ge:m x y)
(geu:m x y)
Like gt and gtu but test for "greater than or equal".

(le:m x y)
(leu:m x y)
Like gt and gtu but test for "less than or equal".

(if_then_else cond then else)
This is not a comparison operation but is listed here because it is always used in conjunction with a comparison operation. To be precise, cond is a comparison expression. This expression represents a choice, according to cond, between the value represented by then and the one represented by else.

On most machines, if_then_else expressions are valid only to express conditional jumps.

(cond [test1 value1 test2 value2 ...] default)
Similar to if_then_else, but more general. Each of test1, test2, ... is performed in turn. The result of this expression is the value corresponding to the first non-zero test, or default if none of the tests are non-zero expressions.

This is currently not valid for instruction patterns and is supported only for insn attributes. See section 20.17 Instruction Attributes.

[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

This document was generated by Vincent Chung on June, 26 2001 using texi2html